Neuigkeiten in RF-HUB

• A phone left on the hub's page in a pocket no longer eats the hub's memory. A hidden tab drops its connection after a minute and reconnects when shown again; a client that stops reading is closed after ten seconds and the page reconnects by itself; and the hub keeps at most four queued frames per page instead of thirty-two.
• A hub with Home Assistant or the app switching many devices no longer restarts at random. The list of devices waiting to be saved was written from several tasks at once; it is now guarded, and saves always happen in one place.
• Opening the schedule or automation page no longer restarts the hub when a schedule, an automation or the app has tried to switch a device that has since been removed.
• The web page answers "low on memory, reload in a moment" instead of restarting the hub when it is asked for the page while memory is scarce.
• A hidden Wi-Fi network can now be chosen. The network list has an "Other network" entry where the name is typed in.
• More free memory for hubs with Home Assistant and many devices. Internal working areas that were never more than a quarter used have been trimmed, giving back about 22 kB to the parts of the hub that need it.
• The status page shows the hub's clock, so a time-related question can be checked at a glance.
• Fixes a memory waste during backups when the cloud link was momentarily busy.

• Same content as 5.2.14, rebuilt for the hubs that could not be re-offered 5.2.14.

• A web page left open no longer burdens the hub. The schedule, automation, info, network and update pages used to ask the hub for everything again every five seconds for as long as they were open, even in a background tab. They now update when something changes, pause while the tab is hidden, and the hub ignores repeated identical requests from older cached pages.
• Support can read the hub's full status through the cloud, so a memory or radio question can be answered without a visit or a cable.

• The hub no longer restarts when its radio stops answering. In rare cases the radio could stop responding to the hub, and the hub would then restart on its own after a short while. It now wakes the radio up again and keeps running.

• Fixes a fault in the hub's status page data introduced earlier the same day (5.2.11 was replaced before reaching more than the first hubs).
• A hub with many devices no longer runs short of memory while its web page is open. Every switch command - from a schedule, an automation, Home Assistant or the app - used to resend the complete device list to the page, and on a hub with 25 or more devices that was enough to drop connections and restart the hub. The page now receives just the value that changed, and the full list only when a device is added, removed or renamed, sent in small pieces with a pause between them.
• The automation and schedule pages no longer restart a hub with many devices. Opening either page built the complete device list in memory at once; on a hub with 45 devices that was enough to crash it. Both pages now receive the list in small pieces, like the device page.
• The local device API and webhook name lookups no longer build the whole device list in memory, and the hub now records where it stood when its free memory hit its lowest point, so the next such dip can be traced.
• An automation rule runs once per button press. A remote repeats its signal several times within one press, and each repeat used to run the rule again - a toggle could land on either state.

• A hub that had run out of room takes new devices again. Device records are stored far more compactly, and a hub that is already full converts its own records one at a time after the update — no reset, nothing to do.
• Switches and dimmers come back the way you left them after a power cut, and sensor readings survive a restart.
• Home Assistant connects on the first try. About one start in three, the first connection to the MQTT broker stalled for a few seconds and the hub ran short of memory while it waited; it recovered on the retry, but readings in that window were lost. Fixed at the root.
• The hub finds its way back to qtrl.me by itself if the connection dies quietly. It used to be able to sit for a day with working Wi-Fi and a working radio while the app showed it as offline.

A calmer restart, especially with many devices

• The hub takes it more gently when it restarts. It sends its device list to qtrl.me in batches and waits until it has room to spare before it connects to Home Assistant. On hubs with a lot of devices this was what could make them unsteady for the first minute after a restart.
• Your devices appear in Home Assistant a little later after a restart than they used to. Nothing is lost — it just arrives at a calmer pace.
• The receiver stays switched on while the hub sends a command, instead of being built up again every time. When that rebuild failed, the hub could be left unable to hear anything for hours.

What you get when you update from 5.0.

More sensors, fewer readings lost

• The hub hears sensors that sit far away or run on weak batteries better than before.
• Oregon sensors that went quiet on 5.1 work again — THGR810 thermometers, PCR800 rain gauges and WGR800 wind sensors.
• New support: Oregon rain gauges PCR122 and RGR968, the Cotech / Kjell & Co weather station with rainfall, light and UV, the Sonoff RM433R2 remote and the vidaXL / WISTAR 1101 awning.
• Thermometers in the Nexus / Rubicson family (MarQuant, Bright, Clas Ohlson) show humidity when they measure it.
• Reception no longer stops working after the hub sends a command.

More from your rain gauge

• Rain right now in mm/h, rain today that starts over at midnight, and a counter of your own that you reset whenever you like.

Easier to keep tidy

• Every device shows its signal strength, so you can see which ones are struggling.
• When a sensor takes a new identity after a battery change, merge it with the old one. Your rain totals carry across.
• Correct a thermometer that reads a degree off.
• Delete all devices with one button when you want to start over.

Home Assistant

• Your own names are the ones Home Assistant shows.
• Values are still there after Home Assistant restarts.
• Devices you add or remove show up and disappear straight away.
• The connection stays steady even with a lot of sensors.

You decide when the hub updates itself

• New setting: auto-update. Tick it and new software is installed when it is released.
• The update page is clearer, and the button says which version it will install.

Safer and steadier

• The hub no longer restarts by itself during an update or when it has a lot to do.
• Support can see how your hub is doing and help you with a setting without a house call. Your Wi-Fi details and a factory reset can never be reached from outside.
• The remote-access link to qtrl.me is only shown for the first ten minutes after the hub has been powered on.

Control Somfy blinds & awnings

• Somfy RTS blinds and awnings — open, close and stop your Somfy motors, and hold the button to run a motor to any position. Pair them straight from the hub.

A more reliable hub

• Rock-solid connection during heavy use — the hub now stays connected to Home Assistant and your smart-home services even when you're sending lots of commands at once. No more dropouts while controlling many devices.

Try new features early

• Test versions — turn on "Receive test versions" under Firmware to try upcoming features before they're officially released. You can always switch back to the latest stable release.

Easier to use

• See the firmware version at a glance, with a friendly reminder when an update is available.
• Hold to move — press and hold Up or Down on a blind to run the motor; release to stop.
• Status light — the hub's LED now tells you what it's doing at a glance: green means running (with a brief wink every few seconds so you know it's alive), white while starting up, blue in setup mode, yellow while connecting to Wi‑Fi, and a red blink if something's wrong. You can set its brightness under Settings.
• Clearer setup when adding channels, and a fix so blinds show the right control type.

RF Signal Tools

• Record and visualise live RF signals — see exactly what your remotes are transmitting
• Replay recorded signals to test and troubleshoot before setting up devices
• Save favourite signals for quick access and one-tap retransmission
• Must be enabled under Advanced Settings

Custom Remotes

• Create custom remotes for any 433MHz device — garage doors, blinds, legacy switches
• Automatic signal matching — the hub recognises when you press a learned remote
• RF1 format — compact signal encoding for reliable storage and matching

New Device Support

• Luxorparts 50219 / RSL366 — full support for Rising Sun tri-state remotes and switches
• Improved Unitec EIM-209 support — better ON/OFF detection, rolling code storage

Home Assistant & MQTT

• MQTT traffic counters — see TX/RX message count and bytes on the HA settings page
• More stable MQTT connection — increased keepalive, faster reconnect
• Smarter send queue — duplicate commands are cancelled, preventing unnecessary transmissions

Battery Status

• Battery indicator on device cards — green for OK, red for low
• Battery status in Home Assistant — automatic binary sensor for supported devices

Stability

• Crash reporting — the hub now reports crash details for faster troubleshooting
• Fixed WebSocket disconnects during RF transmissions
• Fixed watchdog triggers when sending many commands at once
• CC1101 boot hang fix — reliable startup after power loss

Schedule & Automation

• System actions — schedules and automations can now trigger reboot or firmware update
• Smarter state options — dropdowns adapt to the selected device type

Devices

• Fix bug in A-OK/AC123 roller blind support
• Add discovery toggle to disable/enable new device discovery

• Add qtrl.me support for changing device hidden state and item name/order
• Fix sync device/item name changes to qtrl.me

• Static IP configuration — Network page now supports configuring a static IP address, subnet mask, gateway, and DNS server as an alternative to DHCP.
• Improve loading of web GUI
• Improve HA/Mqtt connection stability
• Allow anonymous MQTT connections (empty user/password)

• Improved backup and restore functionality

Bugs

• Fix a bug cause problem save schedules

NOTE: This update takes longer than usual (5 min), and the LED will flash in various colors during the process. Please be patient and do not remove the USB until the update is complete. 

Changes:
Updated the storage model to support additional functions.

Improve Nexa Remote support (support more remotes)
Fix a bug when dimming from Home Assistant
Fix update of inactive or hidden devices in GUI

Fix Oregon sensor issues and add more sensors.
Add support for Sonoff Remotes and Generic RF devices.
Allow disabling connection to Qtrl.Me.
General GUI improvements.

Fixes for support with Homey
Complete GUI redesign with modern interface and improved user experience
Enhanced device sorting algorithm in Web GUI
Improved hub name change handling and synchronization
Added support for Bofu roller blind devices
Added endpoint ordering and custom naming functionalityDisplayed Hub name in GUI interface

Prepare for integration with Homey (Show secret)
Fix support for Clasolsson EMW100R / Everflourish
Add support for Weatherstation Telldus/Luxpart (Kjell&Co)
Fix issue that cause hub to restart when sending many request quickly from HA
Add type interval for Schedule events
Improve Web GUI

Fix /status endpoint
Better wifi connection

• Update GUI
• Fix version handling
• Fix read from flash more stable